B160-101-HDSI - Tripp Lite HDMI/DVI OVER IP TRANSMITTER & RECEIVER KIT W/RS-232 1080P TAA

The B160-101-HDSI HDMI over IP Gigabit LAN Ethernet Extender Kit extends and distributes HDMI or DVI audio/video, RS-232 serial and IR (infrared) remote signals from the source to the display located up to 328.08-ft. (100 m) away, which is more than 200-ft. (60.96 m) farther than a traditional Cat5e/6 solution. By adding a chain of low-cost unmanaged network switches, such as Tripp Lite's NG5, you can continue extending the distance between source and display up to 328.08-ft. (100 m) per switch. Create a multi-in, multi-out installation with up to 64 transmitters and 255 receivers* by including dedicated managed Ethernet network switches** with Internet Group Management Protocol (IGMP), such as Tripp Lite's NSS-G16D2. With a compatible B160-Series receiver, you can send the HDMI or DVI video source (a DVI adapter cable is included) to any analog or digital display, including VGA and DisplayPort™, allowing you to mix and match technologies and use existing monitors. The IGMP-enabled switch will let you manage all connections for centralized control over which sources show on which displays. The B160-101-HDSI supports video resolutions up to 1920 x 1080 (1080p) at 60 Hz in a point-to-multipoint switch installation. It extends IR control signals that control a source, such as a Blu-ray™ player, to a remote display, as well as RS-232 signals at serial baud rates up to 57600 Bps. The transmitter and receiver units mount to a wall, rack or pole using the including hardware. *Unmanaged switch installations are limited to two transmitter units. Number of receivers is limited to number of ports remaining on unmanaged switch. **B160-Series designed for use with dedicated network switch. Connecting to a switch used with other networking equipment will result in degraded or non-functional performance. Extends and Distributes HDMI/DVI A/V, Serial and IR Control Signals over Cat5/6 Cabling Converts audio/video to an IP-based signal that is transmitted point-to-point to a display 328.08-ft. (100 m) away Add low-cost network switches between transmitter and receiver to continue extending distance up to 328.08-ft. (100 m) per switch HDMI output on transmitter for connecting a local display Create a Multi-In, Multi-Out Installation Using B160-Series Transmitters and Receivers Connect up to 64 transmitters and 255 receivers through multiple dedicated managed network switches IGMP-enabled switches allow centralized control over which sources show on which displays Video source can be sent to any analog or digital display, so you can mix and match technologies and use existing monitors Enhanced Technical Features Supports video resolutions up to 1920 x 1080 (1080p) @ 60 Hz Uses H.264 video compression standard Transmits on 20-60 kHz IR frequency Extends IR control signals that control a source from a remote display Supports RS-232 serial baud rates up to 57600 Bps HDCP and 3D compatible Plug-and-Play Functionality No software or drivers required Hardware included for mounting on wall, rack or pole TAA-Compliant Compliant with the Federal Trade Agreements Act (TAA) for GSA Schedule purchases

 

Specification:

 

Features
Material	Metal
Colour depth	24 bit
3D	Yes
Maximum refresh rate	60 Hz
Certification	CE, FCC, REACH
Type	AV transmitter & receiver
Maximum resolution	1920 x 1080 pixels
Cable types supported	Cat5, Cat6
Maximum transfer distance	7874" (200 m)
LED indicators	Yes
Cable length	53.9" (1.37 m)
Product colour	Black
Extended display identification data (EDID)	Yes
Ports & interfaces
3.5 mm (1/8-inch) out	Yes
3.5 mm (1/8-inch) in	Yes
Ethernet LAN	Yes
RJ-45 input ports	1
RJ-45 output ports	1
HDMI in	2
Number of HDMI outputs	1
Connectivity technology	Wired
Power
Input current	0.5 A
Output current	2 A
AC input voltage	100 - 240 V
AC input frequency	50/60 Hz
Operating voltage	5 V
Operational conditions
Storage relative humidity (H-H)	0 - 85%
Operating relative humidity (H-H)	0 - 85%
Storage temperature (T-T)	-15 - 50 °C
Operating temperature (T-T)	0 - 40 °C
Weight & dimensions
Receiver weight	3.31 lbs (1.5 kg)
Transmitter weight	3.31 lbs (1.5 kg)
Width	3.94" (100 mm)
Transmitter dimensions (WxDxH)	3.94 x 5.04 x 1.17" (100 x 128 x 29.7 mm)
Receiver dimensions (WxDxH)	3.94 x 5.04 x 1.17" (100 x 128 x 29.7 mm)
Height	1.17" (29.7 mm)
Depth	5.04" (128 mm)
Packaging data
Package depth	13.4" (340.4 mm)
Package width	4.7" (119.4 mm)
Package height	10.8" (274.3 mm)
Package weight	7.8 lbs (3.54 kg)
Packaging content
Mounting kit	Yes
Cables included	AC, IR
AC adapter included	Yes
Manual	Yes
Included power plug types	AU, EU, NA, US
Technical details
Country of origin	Taiwan
Sustainability certificates	RoHS
Logistics data
Master (outer) case width	13.4" (340.1 mm)
Master (outer) case length	10.9" (277.9 mm)
Master (outer) case height	4.92" (125 mm)
Master (outer) case gross weight	9.11 lbs (4.13 kg)